DELL EMC D-PE-OE-23 Übungsprüfungen
Zuletzt aktualisiert am 08.05.2025- Prüfungscode: D-PE-OE-23
- Prüfungsname: Dell Technologies PowerEdge Operate 2023
- Zertifizierungsanbieter: DELL EMC
- Zuletzt aktualisiert am: 08.05.2025
An engineer needs to install an additional PSU on an existing, single PSU Dell EMC PowerEdge R740. They complete the initial installation and cabling procedures. They connect an AC cable and the power distribution unit produces normal AC output. The engineer checks power management and sees that the new PSU is in the Failed state.
What task should be completed to troubleshoot this issue?
- A . Confirm the System Input Power CAP is not set to Low
- B . Set the PSU AC redundancy to 1+1
- C . Set the PSU AC redundancy to 1+0
- D . Verify the new PSU is the same type and wattage rating
A technician is setting up a previously used Dell EMC PowerEdge server. Upon power up, the PERC alerts them to the presence of a foreign configuration. In the iDRAC storage section, the technician checks Foreign View. The foreign array configuration is the same as the configuration needed for the new project.
What is a recommended way to prepare the disks for the new project?
- A . Access the Ctrl+R utility, clear the foreign configuration, and set up array as needed
- B . Import the foreign configuration and perform a full initialization
- C . Format the foreign configuration and clear the controller configuration
- D . Edit the foreign configuration and set it to Ready
A technician is ready to deploy a server. If a critical part such as the system board fails, they must be able to replace the system board, reconfigure components, and update the firmware revisions in the fastest possible time.
How should the technician meet this requirement?
- A . Back up the profile using the System Profile Settings
- B . Use the iDRAC Rollback feature to restore the firmware revisions
- C . Use the iDRAC GUI to back up the Server Profile
- D . Back up component configurations using iSM
A technician has a server in production. The iDRAC SEL log indicates a possible issue with DIMMs A1 and A2. Firmware is up to date.
What is the most efficient way to troubleshoot this issue?
- A . Reseat DIMMs A1 and A2
- B . Swap DIMMs A1 and A2 to B1 and B2
- C . Swap DIMMs A1 and A2 to A3 and A4
- D . Swap DIMMs A1 and A2 to B1 and B3
An existing server is transferred to a new location. When the iDRAC port is plugged into the network, it causes an IP conflict. The technician is directed to change iDRAC settings via the LCD Front Panel Display. There is NO option to make changes.
What is the most probable cause of this issue?
- A . The LCD Front Panel Display can only be used for initial iDRAC configuration.
- B . iDRAC settings can NOT be changed from LCD Front Panel once the OS has started.
- C . LCD Front Panel Display functionality has been limited to view only state in iDRAC
- D . iDRAC port settings can NOT be configured via LCD Front Panel Display.
Which mobile devices are supported by Quick Sync 2.0 in 14G PowerEdge servers?
- A . iOS devices only
- B . iOS and Android devices only
- C . iOS, Android, and Windows Phone devices
- D . Android devices only
A technician is completing initial firmware updates on a server. One of the updates is a power supply update. During the update process, the server powers off. When the technician hits the power button, they do not see any response from the server.
What is the cause of this issue?
- A . Server lost power
- B . Control panel or power button failed
- C . Front power button is not operational during an update; the technician should use the rear power button.
- D . PSU firmware may now be corrupted
A technician needs to configure a server to PXE boot a server setup image with the BIOS in UEFI mode.
What action is required to enable this function?
- A . Boot to Ctrl+S and configure the NIC for PXE Device1
- B . From the iDRAC web interface, select Network Settings, and enable PXE Device1
- C . Navigate to Boot Options Settings and set PXE Device1 as first option
- D . Navigate to Network Settings, PXE Device1 Settings, and configure IP
A technician recently installed a supported third-party PCIe expansion card and updated the iDRAC firmware on a server. The server is now experiencing internal temperatures that are higher than normal. A second technician is troubleshooting the server and discovers that the expansion card is hot to the touch.
What should the technician do to resolve this issue?
- A . Adjust the Multi Vector Cooling values.
- B . Adjust the power settings.
- C . Reseat all the fans.
- D . Replace the fans one at a time until the faulty fan is identified.
A technician recently installed a supported third-party PCIe expansion card and updated the iDRAC firmware on a server. The server is now experiencing internal temperatures that are higher than normal. A second technician is troubleshooting the server and discovers that the expansion card is hot to the touch.
What should the technician do to resolve this issue?
- A . Adjust the Multi Vector Cooling values.
- B . Adjust the power settings.
- C . Reseat all the fans.
- D . Replace the fans one at a time until the faulty fan is identified.