DELL EMC D-PE-OE-23 Übungsprüfungen
Zuletzt aktualisiert am 05.05.2025- Prüfungscode: D-PE-OE-23
- Prüfungsname: Dell Technologies PowerEdge Operate 2023
- Zertifizierungsanbieter: DELL EMC
- Zuletzt aktualisiert am: 05.05.2025
A technician needs to install several firmware updates on a server. The server cannot be rebooted until the customer performs a routine reboot.
What method should the technician use?
- A . Upload all the firmware revisions using the Lifecycle Controller and then click Install Next Reboot.
- B . Upload all the firmware revisions using the iDRAC and then select install Non-Reboot Only
- C . Compress all the firmware revisions into a zipped file then use the iDRAC to upload and select Install Next Reboot
- D . Upload all the firmware revisions using the iDRAC and then click Install Next Reboot.
The iDRAC is listening for its IP address on its dedicated network port which was configured.
Which connection method(s) can a server administrator use to remotely log in to the iDRAC, even while the server is powered off?
- A . Dell Tools via REPOMAN
- B . Web GUI and SSH CLI
- C . Web GUI and DRM
- D . Dell Tools via DRM
A technician needs to use the iDRAC GUI to update the server using a custom repository hosted on an internal anonymous FTP. The technician receives an error message when trying to update. Catalog.xml not found.
What should the technician do to run updates?
- A . Verify that the FTP service is running on the iDRAC
- B . Enable FTP protocol in the Lifecycle Controller
- C . Update the catalog filename m the System Setup > iDRAC Settings
- D . Specify the catalog name in Catalog Filename
You must configure a BOSS card with 2 x 120GB drives for a Dell EMC PowerEdge server.
What is the only supported mode?
- A . RAID 1
- B . Non-RAID Mirroring
- C . RAID 5
- D . RAID 0
A server has the following configuration:
– 5x 1 TB drives configured in a RAID 5 array
– 1x 1 TB as a global hot spare
– Persistent Hot Spare Slot enabled
A user adds one additional 2 TB drive to the existing array using RAID migration.
How much disk space is available to the operating system?
- A . 5 TB
- B . 6 TB
- C . 7 TB
- D . 8 TB
What type of fans are installed in servers with NVMe storage and GPU configurations?
- A . STD
- B . HPR
- C . LFM
- D . VHP
A technician needs to update the iDRAC license on a PowerEdge R740 server from Express to Enterprise.
The server has the following components:
– 2x CPUs
– 384 GB RAM
– 6x 1 TB drives
– 1x PSU
The server is powered down but connected to active AC. The user wants it to stay powered down and not connect to any networks. No errors are presently displayed.
How can the technician upgrade the license?
- A . The license cannot be upgraded because the user will not allow the server to be powered on
- B . The license cannot be upgraded on a single PSU system
- C . Power on the server then connect to the iDRAC and upgrade iDRAC license before powering the server down
- D . Connect to the iDRAC GUI and upgrade the iDRAC license while the server is powered down.
A technician needs to update the iDRAC license on a PowerEdge R740 server from Express to Enterprise.
The server has the following components:
– 2x CPUs
– 384 GB RAM
– 6x 1 TB drives
– 1x PSU
The server is powered down but connected to active AC. The user wants it to stay powered down and not connect to any networks. No errors are presently displayed.
How can the technician upgrade the license?
- A . The license cannot be upgraded because the user will not allow the server to be powered on
- B . The license cannot be upgraded on a single PSU system
- C . Power on the server then connect to the iDRAC and upgrade iDRAC license before powering the server down
- D . Connect to the iDRAC GUI and upgrade the iDRAC license while the server is powered down.
What processor is used in the iDRAC9 with Lifecycle Controller?
- A . RISC-based processor @800 MHz, with 512 KB L2 cache
8 GB NAND along with HTML5 GUI - B . Dual core E3 processor @800 MHz, with 512 KB L2 cache
8 GB NAND along with Java interface - C . Dual core ARM A-9 processor @800 MHz, with 512 KB L2 cache
8 GB NAND along with HTML5 GUI - D . Quad core processor @1.2 GHz, with 512 KB L2 cache
8 GB NAND along with Java interface
What is the default location of the extracted files of the OMSA installer?
- A . C:Program FilesSystem32
- B . C:OpenManage
- C . C:WindowsTemp
- D . Current directory