HP HPE6-A85 Übungsprüfungen
Zuletzt aktualisiert am 06.05.2025- Prüfungscode: HPE6-A85
- Prüfungsname: Aruba Certified Campus Access Associate Exam
- Zertifizierungsanbieter: HP
- Zuletzt aktualisiert am: 06.05.2025
You are in a meeting with a customer where you are asked to explain how the network redundancy feature VRRP works.
What is the correct statement for this feature?
- A . VRRP uses BPDUs for messaging
- B . VRRP uses multicast for messaging
- C . VRRP uses unicast for messaging
- D . VRRP uses broadcast for messaging
Based on the "show ip route" output on an Aruba CX 8325, what type of route is "10.20.0.0/22, vrf default via 10.1.1.1, [110/200]"?
- A . connected
- B . local
- C . OSPF
- D . static
You need to ensure that voice traffic sent through an ArubaOS-CX switch arrives with minimal latency.
What is the best scheduling technology to use for this task?
- A . QoS shaping
- B . Rate limiting
- C . Strict queuing
- D . DWRR queuing
After having configured the edge switch uplink as requested your colleague says that they have failed to ping the core You ask your colleague to verify the connection is plugged in and the switch is powered on They confirm that both are correct You attempt to ping the core switch and confirm that the ping is failing.
Knowing the nature of this deployment, what commands might you use to troubleshoot this issued
- A . Ping 10.11 1 – ping the core to attempt to verify connectivity Show trunk – to verify if the LAG interface was correctly added to the switch Show spanning tree – to check for spanning-tree blocked states Show port-access clients interface all – to view any port-access blocking states or failed authentication attempts on all interfaces Show run interface vlan20 – to double check the layer 3 svi configuration is correct for l_3 connectivity Show lldp neighors – to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports
- B . diagnostic diag cable-diag 1/1/51 diag cable-diag 1/1/52 – to view diagnostic information for the physical link to get a status on any interruptions to Layer 1 connectivity, show ip route – to verify that the default gateway is present in the routing table show ip ospf – to check whether there is a layer 3 routing protocol enabled show ip dns – to view whether there is a valid dns source
- C . Ping 10.1.1.1 – ping the core to attempt to verify connectivity show lacp agg – to verify which link aggregations are currently configured using which physical ports show lacp int – to verify the LACP status and whether any links are blocking in your topology show lldp neighors – to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports show run interface 1/1/51.1/1/52-to ensure the physical interfaces are no-shut and members of the lag show run interface lag 1 – to ensure the correct vlan trunking configuration is applied to the logical interface show run int vlan 20 – to ensure you have the L3 SVI no shut and configured in the correct subnet
- D . Show run – to view the running configuration of the switch Show run | begin 20 "vlan 20" – to ensure VLAN 20 was correctly added to the database show run | begin 20 ‚interface vlan 20‘ – to view the L3 SVI configuration Show run interface 1/1/51.1/1/52 – to ensure the physical interfaces are no shut and were added as members of LAG 1 Show run int lag 1 – to verify LACP mode active was configured to eliminate LACP blocking states
What is an advantage of using Layer 2 MAC authentication?
- A . it matches user names to MAC address
- B . No setup is required on the client
- C . MAC allow lists are easily maintained over time
- D . MAC identifiers are hard to spoof
What are two advantages of a UXl? (Select two.)
- A . A UXl can be used without any internet connection
- B . A UXl helps to calculate the best WiFi channels in a remote location
- C . A UXl behaves like a client/user
- D . A UXl measures the Wi-Fi coverage of all APs in the given location.
- E . A UXl can check different applications, such as HTTP VOIP or Office 365.
What is indicated by a solid amber radio status LED on an Aruba AP?
- A . Not enough PoE is provided from the switch to power both radios of the AP
- B . The radio is working in mesh mode
- C . The radio is working the 5 GHz band only.
- D . The radio is enabled in monitor or spectrum analysis mode
A network technician is testing a new SSID for a branch office. They are able to connect, get an IP address, and resolve DNS names. However, they are not able to browse the internet.
On the existing SSID at the branch, connectivity to the internet works as expected on the same VLAN as the new SSID. The wireless client should have received a new role to allow internet access.
What should the network technician verify to ensure both SSIDs function in a similar way?
- A . Verify each SSID’s authentication and encryption parameters are enabled and the same.
- B . Verify that the implicit ‚deny all‘ is the last entry in the firewall policies.
- C . Verify the new SSID is broadcasting on all the APs at the branch office.
- D . Verify the firewall policies assigned, making sure the rules are correct and ordered properly.
What information is required when using the ClearPass self-service registration page to generate a Multiple Pre-Shared Key (MPSK) for headless devices?
- A . The device’s model number
- B . The device’s MAC address
- C . The device’s IP address
- D . The device’s OS type