HP HPE7-A01 Übungsprüfungen
Zuletzt aktualisiert am 05.05.2025- Prüfungscode: HPE7-A01
- Prüfungsname: Aruba Certified Campus Access Professional Exam
- Zertifizierungsanbieter: HP
- Zuletzt aktualisiert am: 05.05.2025
Match the topics with the underlying technologies (Options may be used more than once or not at all.)
Match the solution components of NetConductor (Options may be used more than once or not at all.)
With Aruba CX 6300. how do you configure ip address 10 10 10 1 for the interface in default state for interface 1/1/1?
- A . int 1/1/1. switching, ip address 10 10 10 1/24
- B . int 1/1/1. no switching, ip address 10 10 10.1/24
- C . int 1/1/1. ip address 10.10.10.1/24
- D . int 1/1/1. routing, ip address 10.10.10 1/24
With the Aruba CX 6100 48G switch with uplinks of 1/1/47 and 1/1/48.
H ow do you automate the process of resuming the port operational state once a loop on a client port is cleared?
- A . Configure int 1/1/1-1/1/52 loop-protect disable timer.
- B . Configure global loop-protect disable timer.
- C . Configure int 1/1/1-1/1/46 loop-protect re-enable-timer.
- D . Configure global loop-protect re-enable-timer.
You are setting up a customer’s 15 headless loT devices that do not support 802.1X..
What should you use?
- A . Multiple Pre-Shared Keys (MPSK) Local
- B . Clearpass with WPA3-PSK
- C . Clearpass with WPA3-AES
- D . Multiple Pre-Shared Keys (MPSK) with WPA3-AES
You are setting up a customer’s 15 headless loT devices that do not support 802.1X..
What should you use?
- A . Multiple Pre-Shared Keys (MPSK) Local
- B . Clearpass with WPA3-PSK
- C . Clearpass with WPA3-AES
- D . Multiple Pre-Shared Keys (MPSK) with WPA3-AES
A new network design is being considered to minimize client latency in a high-density environment. The design needs to do this by eliminating contention overhead by dedicating subcamers to clients.
Which technology is the best match for this use case?
- A . OFDMA
- B . MU-MIMO
- C . QWMM
- D . Channel Bonding
You are helping an onsite network technician bring up an Aruba 9004 gateway with ZTP for a branch office The technician was to plug in any port for the ZTP process to start Thirty minutes after the gateway was plugged in new users started to complain they were no longer able to get to the internet. One user who reported the issue stated their IP address is 172.16 0.81 However, the branch office network is supposed to be on 10.231 81.0/24.
What should the technician do to alleviate the issue and get the ZTP process started correctly?
- A . Turn off the DHCP scope on the gateway, and set DNS correctly on the gateway to reach Aruba Activate
- B . Move the cable on the gateway from port G0/0V1 tc port GO 0.0
- C . Move the cable on the gateway to G0/0/1. and add the device’s MAC and Serial number in Central
- D . Factory default and reboot the gateway to restart the process.
A company deployed Dynamic Segmentation with their CX switches and Gateways After performing a security audit on their network, they discovered that the tunnels built between the CX switch and the Aruba Gateway are not encrypted. The company is concerned that bad actors could try to insert spoofed messages on the Gateway to disrupt communications or obtain information about the network.
Which action must the administrator perform to address this situation?
- A . Enable Secure Mode Enhanced
- B . Enable Enhanced security
- C . Enable Enhanced PAPI security
- D . Enable GRE security
You are deploying a bonded 40 MHz wide channel.
What is the difference in the noise floor perceived by a client using this bonded channel as compared to an unbonded 20MHz wide channel?
- A . 2dB
- B . 3dB
- C . 8dB
- D . 4dB