Huawei H13-629_V3.0-ENU Übungsprüfungen
Zuletzt aktualisiert am 02.05.2026- Prüfungscode: H13-629_V3.0-ENU
- Prüfungsname: HCIE-Storage (Written) V3.0
- Zertifizierungsanbieter: Huawei
- Zuletzt aktualisiert am: 02.05.2026
In the process of tuning storage layer performance, which of the following steps includes tuning operation preparation and tuning configuration?
- A . Tuning Operations
- B . Tuning Analysis
- C . Test and Application
- D . Information Collection
What factors are related to Huawei storage heterogeneous migration bandwidth assessment? (Multiple choice)
- A . Number of migration tasks
- B . Number of target storage controllers
- C . Number of migration ports
- D . LUN migration rate
What factors are related to Huawei storage heterogeneous migration bandwidth assessment? (Multiple choice)
- A . Number of migration tasks
- B . Number of target storage controllers
- C . Number of migration ports
- D . LUN migration rate
Huawei OceanStor all-flash storage system supports IP drift to ensure business continuity and reliability. Which of the following statements about IP drift is wrong?
- A . When "Manual" is selected for the "Failback Mode" of IP drift, the system can switch the service back to the active port only when the active port link is in a normal state and lasts for more than 1 minute when the port failure recovers.
- B . If Ethernet ports A and B are added to VLAN 2, ports A and B belong to the same drift group by default.
- C . An Ethernet port can create multiple logical ports.
- D . If bound port A and physical port B join the same VLAN, as long as one physical port in bound port A fails, the service will be switched to physical port B.
When configuring the SmartMigrationt feature in Huawei All-Flash Storage to perform data migration, if new business data is delivered, changes need to be synchronized during the migration process.
Which of the following analyses of the change synchronization process are correct? (Multiple choice)
- A . The application host will write the business data changes to both the source LUN and the target LUN through dual writing.
- B . The storage system will write business data changes to both the source LUN and the target LUN through dual writing.
- C . If the source LUN fails to be written, the storage system will return a message that the application host has failed to write I/O. The host needs to resend data to the source LUN and target LUN.
- D . If the target LUN fails to be written, the storage system will copy the unsynchronized data recorded on the DCL to the target LUN.
Which of the following storage architectures are scalable? (Multiple choice)
- A . DAS
- B . NAS
- C . FC SAN
- D . IP SAN
Bank A purchased all-flash storage using the SmartMatrix fully interconnected high-reliability architecture to ensure that its core business remains online.
Which of the following statements are correct about the characteristics of this architecture? (Multiple choice)
- A . Full sharing of front-end cards
- B . Controller full interconnection port
- C . Disk-frame cross-engine interconnection
- D . Controller failure switching within seconds
Huawei’s hyper-converged storage has a parallel fast data reconstruction function. Data shards are spread across the resource pool. After a hard disk fails, it can be automatically rebuilt in parallel across the entire resource pool. Only the actual data is rebuilt, without the need for a separate hot spare disk.
- A . True
- B . False
During the configuration of the HyperMetro active-active domain, if the remote device cannot be automatically listed in the configuration interface, which of the following are the possible reasons? (Multiple choice)
- A . The device type of the remote device is.
- B . The remote device has been added to another active-active domain.
- C . The remote device has an alarm "The remote device has no backup link"
- D . The health status of the remote device is not "normal".
A bank plans to purchase a set of distributed storage and sends the requirements to multiple storage equipment suppliers. The bank’s storage engineer conducts industry comparison and communication based on the requirements, determines the appropriate equipment technical standards, selects three suppliers for equipment testing, and finally outputs a report. This is an operation in the equipment selection stage.
- A . True
- B . False