Network Appliance NS0-184 Übungsprüfungen
Zuletzt aktualisiert am 25.05.2025- Prüfungscode: NS0-184
- Prüfungsname: NetApp Certified Storage Installation Engineer, ONTAP
- Zertifizierungsanbieter: Network Appliance
- Zuletzt aktualisiert am: 25.05.2025
You have a 4-node FAS8060 cluster. You are using the vol move command to relocate a volume from an aggregate on node 1 to an aggregate on node 4.
In this scenario, which network is used for the traffic being relocated?
- A . the node management network
- B . the HA interconnect
- C . the Intercluster network
- D . the cluster interconnect
On a new installation, you have identified that the components required to perform the task are not all functional. One of the controllers in the cluster fails to see any disks and cannot join the cluster.
Which response to the customer indicates that you are in control of the situation?
- A . “A failed component has been identified. I will reschedule when you receive the new part.”
- B . “A failed component has been identified. It will stop the installation for now.”
- C . “A failed component has been identified. What do you want me to do about it?”
- D . “A failed component has been identified. I have contacted support and here are your options…”
You want to create a data volume on aggr0 and you receive a message with the following warning: “Warning: You are about to create a volume on a root aggregate.
This may cause severe performance or stability problems and therefore is not recommended. Do you want to proceed?“
What is the reason for this severe performance or stability problem?
- A . Controller failover and storage failover are separate processes that must occur in parallel, otherwise problems will arise.
- B . The performance load generated by the data volume can be very strong, so it should not be shared with vol0 on aggr0, requiring a separate aggregate for it.
- C . The performance load generated by the vol0 cannot be shared with any other volume on aggr0, requiring a dedicated aggregate for it.
- D . Controller failover and storage failover are separate processes that must occur at different times, otherwise problems will arise.
You have to disable a switch that is connected to a port on your FAS2750. You notice that the LIFs that are associated with this port are migrated to a port that is not expected.
In this scenario, what would cause this behavior?
- A . The network port is configured incorrectly.
- B . The broadcast domain is configured incorrectly.
- C . There are no online ports within the same failover group.
- D . The network failover port is not licensed.
You have to disable a switch that is connected to a port on your FAS2750. You notice that the LIFs that are associated with this port are migrated to a port that is not expected.
In this scenario, what would cause this behavior?
- A . The network port is configured incorrectly.
- B . The broadcast domain is configured incorrectly.
- C . There are no online ports within the same failover group.
- D . The network failover port is not licensed.
What are two ways to obtain customer licenses for a new ONTAP system? (Choose two.)
- A . Access the NetApp Support site.
- B . Open a support ticket.
- C . Access the Field Portal site.
- D . Access NetApp Knowledge Base.
Exhibit:
While you are showing the NetApp Support website, your customer asks you to ensure that the new ONTAP storage array is covered by support before you complete the knowledge transfer procedure.
Referring to the exhibit, which two widgets would you select to accomplish this task? (Choose two.)
- A . Systems
- B . Contracts and Warranties
- C . Active IQ
- D . Product Support
You are preparing to physically install a new AFF A400 cluster into a customer’s racks. All equipment has been delivered to the customer’s site.
Which three tools do you need to complete this installation? (Choose three.)
- A . additional network cables
- B . Phillips #2 screwdriver
- C . laptop computer
- D . slide rail kit
- E . cable management tray
Given:
Which three classes successfully override printOne()? (Choose three.)
- A . Option A
- B . Option B
- C . Option C
- D . Option D
- E . Option E
- F . Option F
You configured AutoSupport and are trying to send a full AutoSupport message to NetApp. You use the autosupport history show command and see the output shown in the exhibit. The customer confirms that the AutoSupport settings are correct.
Which two actions will solve this issue? (Choose two.)
- A . The customer needs to enable AutoSupport for both nodes.
- B . The customer needs to exclude the two nodes from the attachment-size limitation.
- C . The customer needs to change the transport protocol to HTTP.
- D . The customer needs to white-list the two nodes on their mail server.