Network Appliance NS0-184 Übungsprüfungen
Zuletzt aktualisiert am 26.05.2025- Prüfungscode: NS0-184
- Prüfungsname: NetApp Certified Storage Installation Engineer, ONTAP
- Zertifizierungsanbieter: Network Appliance
- Zuletzt aktualisiert am: 26.05.2025
You just installed two nodes into an existing ONTAP cluster. When running date on the CLI you notice that the cluster1-03 node is running behind time. You confirmed that you can reach the node management LIF of each node.
Referring to the exhibit, which statement is true?
- A . The node-management LIF has to be on e0M for NTP to work.
- B . The DNS is not configured for this node.
- C . The NTP is adjusting in small increments.
- D . No NTP server is configured for this node.
You are preparing for the installation of a new 2-node switchless AFF A250 ONTAP 9.8 cluster and need to obtain the preinstallation information from the customer.
In this scenario, what are three examples of data required from the customer? (Choose three.)
- A . management IP addresses
- B . cluster switch name
- C . gateway IP address
- D . BMC IP addresses
- E . cluster name
How many spare disks are required to activate the maintenance center?
- A . 0
- B . 1
- C . 2
- D . 3
Click the Exhibit button.
You are asked to install a new cluster with six FAS8060 nodes. While running Config Advisor, you see the messages shown in the exhibit. The customer does not want ACP cabled on their cluster.
Which two actions would allow the installation to be completed successfully? (Choose two.)
- A . Advise NGS that the customer has a controller in an unsupported state.
- B . Advise the customer that they must acknowledge that they are not using ACP on the installation.
- C . Advise the sales team that the customer is operating without ACP and that the customer is asking you to leave it that way.
- D . Advise the customer that the error will cause the controller to not operate properly and create an unsupported state.
After installing cluster switches, you want to verify that the switches are operating as they should.
What would allow you to accomplish this task?
- A . Use Config Builder.
- B . Use the cluster ping-cluster command in privilege advanced mode.
- C . Use the network device-discovery command in privilege advanced mode.
- D . Use OnCommand System Manager.
Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.
Which two tools would you use to validate the configuration? (Choose two.)
- A . Interoperability Matrix Tool
- B . Active IQ System Manager
- C . Hardware Universe
- D . Active IQ Config Advisor
You have a 2-node FAS8300 switchless ONTAP 9.8 cluster that serves NAS volumes. You have a data SVM that connects to the network using multimode LACP with VLAN tags.
In this scenario, which front-end FAS8300 network port would you create the data LIFs?
- A . a0a
- B . e0e
- C . e0e-100
- D . a0a-100
After an initial setup, you want to create a new data aggregate. The node has thirty-one 4 TB SATA spare disks assigned. Your customer wants to have two spare disks.
In this scenario, which two settings would you use to reach the maximum capacity and availability? (Choose two.)
- A . -maxraidsize 31
- B . -raidtype raid_tec
- C . -raidtype raid_dp
- D . -maxraidsize 29
You installed a new FAS8200 cluster and are configuring important EMS event notifications to be sent to the customer.
Which address must be set up for e-mail notifications in this scenario?
- A . LDAP address
- B . site address
- C . partner address
- D . mailserver address
You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.
Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)
- A . Use ports from different NICs.
- B . Use ports from the same NICs.
- C . Use ports with different chipsets.
- D . Use ports with the same chipsets.